Oclaro HL63193 638nm 700mw Red Laser Module W/Flexdrive Driver & G-2 Glass Lens

Description

Listing is for a brand new single Oclaro 700mW 638nm laser diode in a standard 12mm copper module with Flexdrive bucking laser driver set to 1.1A and a high pass G-2 glass lens. Copper module provides good thermal conductivity over the standard brass module providing more stable output from the diode. Perfect for running off a single rechargeable 3.7V Li-Ion or a 5V 2A wall adapter. Unit is ready to be dropped into your final project. Just throw in a heatsink and apply power source. Modules are wired with extremely flexible 26AWG wire that is burn proof and makes for very easy soldering.
Here is what you get. The driver is contained in the module.
You can discard the back half if you need the extra room just be careful not to let the driver short on anything.:)
Wire assignment is:
Red +
Black -
Specs
Wavelength                                        638nm +/- 5nm
Input Voltage                                    3.2V-5.5V
Driver Output Current                    1.1A(default)
Driver Current Draw                       950mA +/- 0.5A
Power Output                                   700mW-1W
Driver Type                                      Constant Current
Lens                                                   9mm Threaded Three Element(Aixiz) Glass Lens
Reverse Polarity Protection           Yes
Duty Cycle                                        Continuous with proper heatsinking
Please note
These are multi-mode display diodes similar to the 1W+ 445nm diodes. Check these threads for info on output and beam correction.
Inexpensive, decent correction for 300mW Mitsubishi 635nm laser @ 94% transmission
Rayfoss/Mitsubishi 638nm 300mW laser diode
Mitsubishi ML520G71...Red Holy Grail or Flashlight Fail ??
Here are some more threads about these diodes.
It is Here.!!!!! 300mW "635nm" Mitsubishi.....
Correcting the beam of the 300mW 638nm diodes
Mitsubishi 635nm diode divergence at 350 feet
The "Echo" - 500mW 635nm DIY Red
Mitsubishi 638nm 300mW laser diode melting CD case
Canon DSLR beamshots of 638nm and 445nm laser
.
Running off my bench power supply and encased in a finned heatsink. Check out these awesome shots.(Finned heatsink not included)Running off my bench power supply and encased in a finned heatsink. Check out these awesome shots.(Finned heatsink not included)Running off my bench power supply and encased in a finned heatsink. Check out these awesome shots.(Finned heatsink not included)
Oclaro 700mW 638nm Diode (HL63193MG)
Comparing collimated output with a 500mW Mitsu G71 diode both using a standard G-2 glass lens. They are nearly the same but the G71 still does have a little finer collimation before any correction optics.
Power Test With G-2 Lens
*Disclamer*
By purchasing these diodes you are agreeing to the following.
- You are over 18 years of age .
- You understand that these components that are mentioned above are dangerous when not properly assembled into a finished product.
- You will use these as components and properly incorporate them into a finished product.
- You will use these diodes/modules in a safe and responsible manner and for a legal purpose.
- You are legally responsible for the use of these components, improper use of these components or their end products.
- You are legally responsible for any injury to anybody resulting from the use of or assembly of these components or their finished products.
- You Accept this diode/module as a COMPONENT for integration in a system of YOUR OWN design and will be legally responsible from any and all LIABILITIES These Diodes and Modules are sold solely as a component for incorporation into the customer's end products. Therefore, this diode/module is exempt from compliance with the appropriate requirements of FDA 21CFR, section 1040.10 and 1040.11 for complete products.